100-490 Exam Dumps and Practice Questions

The show cellular unit network command in Cisco IOS is used to view detailed information about the cellular modem and the network it's connected to. Here's the type of information this command usually displays:

Network Status: Whether the device is registered on the cellular network.

Carrier Information: The name of the cellular network provider.

Technology: The cellular technology in use (e.g., 3G, 4G/LTE).

Signal Strength: Signal strength indicators like RSSI and RSCP.

Cell Site Information: Data about the cell tower or base station the device is connected to.

IP Address: The IP address assigned to the cellular interface.

Why other options are less likely:

show cellular unit radio: Provides information about the radio module itself, such as its state and power levels.

show cellular unit hardware: Focuses on hardware-level information of the cellular unit.

show cellular unit profile: Displays configuration details of the cellular profile used to connect to the network.

Cisco command documentation for different show cellular options: https://www.cisco.com/c/en/us/td/docs/routers/wireless-wan/Cisco-Catalyst-Cellular-Gateways/cisco-cellular-gateways-command-reference-guide/m-show_commands.pdf

RJ-45 is the standard connector used for Ethernet networks. Here's why it's the correct answer:

Compatibility: Ethernet ports on both laptops and Cisco switches use RJ-45 connectors. This makes RJ-45 cables ideal for direct connections between these devices.

Appearance: RJ-45 ports are rectangular and slightly larger than typical phone jacks (RJ-11). They have eight metal pins inside.

Why other options are incorrect:

DVI: DVI ports are used for video connections between computers and displays.

RJ-11: RJ-11 ports are primarily associated with analog phone lines and are smaller than RJ-45.

DB-9: DB-9 connectors were traditionally used for serial connections on older computers and peripherals.

This configuration describes a crossover cable. A crossover cable is used to connect two similar devices directly, such as two computers or two switches, without the need for an intermediate device like a router. The wires at one end of a crossover cable are in reverse sequence to the wires at the other end, which allows the transmit and receive signals to be properly aligned between the two devices. This is different from a straight-through cable, where the wire sequence is the same at both ends1.

1. It is built on a client-server model architecture and uses separate control and data connections between the client and the server2. Here are the explanations for the correct answers:

* B: The copy running-config ftp: command is used to copy the running configuration from a router to an FTP server or vice versa. This is a common method for backing up and restoring configurations on Cisco devices1.

* E: FTP typically requires authentication, which means a Cisco router acting as an FTP client must be configured with the appropriate username and password to access an FTP server. This ensures secure file transfer and access control1.

The other options are incorrect because:

* A: FTP is not used to load Cisco IOS Software to a router in ROMMON mode; this is typically done using TFTP or Xmodem.

* C: While a router can act as an FTP server, this is not a description of FTP itself.

* D: FTP uses TCP as its transport protocol, not UDP. FTP needs the reliability that TCP provides because it ensures the complete and accurate transfer of files1.

IPv6 addresses are 128 bits in length and are written as eight groups of four hexadecimal digits. Each group is separated from the others by colons (:). The correct notation for IPv6 addresses allows for the omission of leading zeros within each block of four hexadecimal digits and the use of double colons (::) to represent consecutive blocks of zeros. However, the double colons can only be used once in an address to ensure proper expansion to the full 128 bits. Option B is the only choice that correctly represents a full IPv6 address without any abbreviation.Options A and C use double colons incorrectly, and option D represents a prefix length rather than a full address.Reference:= The information is based on standard IPv6 address notation practices, which include the representation of addresses in hexadecimal format and the rules for abbreviating zeros1