Most Recent Cisco 300-410 Exam Dumps

Prepare for the Cisco Implementing Cisco Enterprise Advanced Routing and Services exam with our extensive collection of questions and answers. These practice Q&A are updated according to the latest syllabus, providing you with the tools needed to review and test your knowledge.

QA4Exam focus on the latest syllabus and exam objectives, our practice Q&A are designed to help you identify key topics and solidify your understanding. By focusing on the core curriculum, These Questions & Answers helps you cover all the essential topics, ensuring you're well-prepared for every section of the exam. Each question comes with a detailed explanation, offering valuable insights and helping you to learn from your mistakes. Whether you're looking to assess your progress or dive deeper into complex topics, our updated Q&A will provide the support you need to confidently approach the Cisco 300-410 exam and achieve success.

The questions for 300-410 were last updated on May 7, 2025.

Viewing page 1 out of 119 pages.
Viewing questions 1-5 out of 594 questions

Get All 594 Questions & Answers

Question No. 1

Refer to the exhibit.

An engineer implemented CoPP but did not see OSPF traffic going through it. Which configuration resolves the issue?

Aip access-list extended OSPF permit ospf any any

Bpolicy-map COPP class OSFP police 8000 conform-action transmit exceed-action transmit violate-action drop

Ccontrol-plane service-policy input COPP

Dclass-map match-all OSFP match access-group name OSPF

Show Answer

Correct Answer: B

Question No. 2

What is a function of BFD?

Apeer recovery after a Layer 3 protocol adjacency failure

Bpeer recovery after a Layer 2 adjacency failure

Cfailure detection independent of routing protocols and media types

Dfailure detection dependent on routing protocols and media types

Show Answer

Correct Answer: D

Question No. 3

Which 0S1 model is used to insert an MPLS label?

Abetween Layer 5 and Layer 6

Bbetween Layer 1 and Layer 2

Cbetween Layer 3 and Layer 4

Dbetween Layer 2 and Layer 3

Show Answer

Correct Answer: D

Question No. 4

What is a limitation of IPv6 RA Guard?

AIt is not supported in hardware when TCAM is programmed

BIt does not offer protection in environments where IPv6 traffic is tunneled.

CIt cannot be configured on a switch port interface in the ingress direction

DPackets that are dropped by IPv6 RA Guard cannot be spanned

Show Answer

Correct Answer: B

Restrictions for IPv6 RA Guard

The IPv6 RA Guard feature does not offer protection in environments where IPv6 traffic is tunneled.

This feature is supported only in hardware when the ternary content addressable memory (TCAM) is programmed.

This feature can be configured on a switch port interface in the ingress direction.

This feature supports host mode and router mode.

This feature is supported only in the ingress direction; it is not supported in the egress direction.

This feature is not supported on EtherChannel and EtherChannel port members.

This feature is not supported on trunk ports with merge mode.

This feature is supported on auxiliary VLANs and private VLANs (PVLANs). In the case of PVLANs, primary VLAN features are inherited and merged with port features.

Packets dropped by the IPv6 RA Guard feature can be spanned.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6_fhsec/configuration/xe-16-10/ip6f-xe-16-10-book/ip6-ra-guard.html#GUID-589AF00C-7499-439F-AD23-51005D61CAB7

Question No. 5

Refer to the exhibit.

Refer to the exhibit. An administrator must upload the packages conf Me to an FTP server. However, the FTP server rejected anonymous service and required users to authenticate What are the two ways to resolve the issue? (Choose two.)

AUse is ftp username and ip ftp password configuration commands to specify valid FTP server credentials.

BUse the copy flash:packages.conf scp: command instead and enter the FTP server credentials when prompted.

CEnter the FTP server credentials directly In the FTP URL using the ftp://username:passwordQ192.0.2.40/ syntax .

DCreate a user on the rooter matching the username and password on the FTP server and log in before attempting the copy

EUse the copy flash-packages conf ftp: command instead and enter the FTP server credent-ais when prompted.

Show Answer

Correct Answer: A, C

Unlock All Questions for Cisco 300-410 Exam

Full Exam Access, Actual Exam Questions, Validated Answers, Anytime Anywhere, No Download Limits, No Practice Limits

Get All 594 Questions & Answers