Most Recent Dell EMC DES-5221 Exam Dumps

Prepare for the Dell EMC Specialist - Implementation Engineer-Data Center Networking exam with our extensive collection of questions and answers. These practice Q&A are updated according to the latest syllabus, providing you with the tools needed to review and test your knowledge.

QA4Exam focus on the latest syllabus and exam objectives, our practice Q&A are designed to help you identify key topics and solidify your understanding. By focusing on the core curriculum, These Questions & Answers helps you cover all the essential topics, ensuring you're well-prepared for every section of the exam. Each question comes with a detailed explanation, offering valuable insights and helping you to learn from your mistakes. Whether you're looking to assess your progress or dive deeper into complex topics, our updated Q&A will provide the support you need to confidently approach the Dell EMC DES-5221 exam and achieve success.

The questions for DES-5221 were last updated on May 3, 2025.

Viewing page 1 out of 12 pages.
Viewing questions 1-5 out of 60 questions

Get All 60 Questions & Answers

Question No. 1

What is required to enable ECMP in BGP?

AOSPF must install equal cost paths in the routing table for BGP to use ECMP.

BMaximum-paths and multipath-relax commands.

CSub-interfaces must be configured on the physical interface running BGP.

DECMP is not possible in BGP.

Show Answer

Correct Answer: B

Question No. 2

Which commands are required to properly configure an OS10 switch to run OSPF on eth1/1/3 and to add network 144.254.1.0/30 to OSPF area 0?

AOS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0
OS10(config)# router ospf1

BOS10(config)# router ospf 1
OS10(config-router-ospf-1)# router-id 1.1.1.1 OS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown OS10(conf-if-eth1/1/3)# no switchport OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0

COS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0 OS10(config)# router ospf 1

DOS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0 OS10(conf-if-eth1/1/3)# router ospf 1

Show Answer

Correct Answer: C

Question No. 3

Which command shows whether a LAG protocol is static or dynamic on a Dell EMC Networking OS10 switch?

Ashow lacp neighbor

Bshow running-configuration lacp

Cshow interface port-channel summary

Dshow port-channel summary

Show Answer

Correct Answer: D

https://topics-cdn.dell.com/pdf/force10-s4048-on_reference-guide6_en-us.pdf

Question No. 4

Which LSA types are used in a single area OSPF topology?

A4, 5 and 7

B1 and 7

C1, 2 and 5

D2, 3 and 5

Show Answer

Correct Answer: C

Question No. 5

There is a spanning tree mismatch at the global level. PVST+ is configured on a VLT peer. All VLT port channels go down on both VLT peers. A syslog error message is generated. What is the correct action to resolve the issue?

AVerify the VLT LAG ID is configured correctly on both VLT peers.

BEnable RSTP on both VLT peers.

CUse the show VLT detail and show VLT brief commands to view the VLT port channel status information.

DPerform a mismatch check after the VLT peer is established.

Show Answer

Correct Answer: D

https://www.dell.com/support/manuals/us/en/04/poweredge-fx2/dell%20fn%20ioa% 20config_9.8.0.0_pub-v1/troubleshooting-vlt?guid=guid-9978ac1f-1305-4590-9c64-bb35bd6e012a&lang=en- us

Unlock All Questions for Dell EMC DES-5221 Exam

Full Exam Access, Actual Exam Questions, Validated Answers, Anytime Anywhere, No Download Limits, No Practice Limits

Get All 60 Questions & Answers